Outlaw Audio home shop products hideout news support about
Topic Options
#99265 - 02/05/22 12:13 PM Trigger operates sporadically
kiwiaudio Offline
Gunslinger

Registered: 01/16/11
Posts: 86
Loc: United States
My 755 has been a great amp. Almost 10 years old now and it still sounds amazing. My trigger turn on circuit is giving me problems however, and im almost 100% sure the 3mm mono socket on back of the 755 is the problem. Fitment, when inserting the cable is loose, as if the contacts inside have relaxed and only touch intermittently. I know the circuit needs to be satisfied all the time, or it powers off. I have 5.5 volts coming out of the trigger ports of my 976 and Outlaw support says that is sufficient. Ive tested this voltage supply from the 976 and it remains constant.
I either need to repair this socket or eliminate the turn on circuit.
Anyone have experience with this issue ?
I see there was discussion about this about 4 years ago, but no resolution was posted !
_________________________
Double drywalled, "Green Glue" treated Theater
GIK acoustic treatment
Epson 8700UB Projecting on a 135" Seymour XD Audio transparent screen
Outlaw 976 Processor
Outlaw 755 amp for Center and all four surrounds
Adcom GFA 555II for Main L & R channels
Behringer EP4000 for two homemade subs
Outlaw Ultra X13 for REAL Sub Bass !
OPPO BDP103, Marantz CD63SE, Denon DP300F
2 Adcom ACE515s for AC current treatment
Newport Theater Director for AC distribution.
Speakers are all built by myself utilizing Dynaudio Drivers
Second room: Yamaha receiver, Musical fidelity X10D tubes, Carver C9 holographic pro.

Top
#99363 - 11/07/24 12:03 PM Re: Trigger operates sporadically [Re: kiwiaudio]
kiwiaudio Offline
Gunslinger

Registered: 01/16/11
Posts: 86
Loc: United States
In the remote chance someone has an idea on this, im adding info.
I dont expect this legacy section gets much attention, but here goes :

The issue is not the trigger as i initially thought. As ive discovered, if i lose trigger voltage at any time, the amp powers off.
With both power switches and the trigger voltage supplied from my Outlaw 976, the amp will not turn on until the Master power switch on the rear panel of the amp is cycled off, then back on. The amp will then power up and run flawlessly for as long as i need it to. Ive checked that the trigger voltage is constant.
No other sequence of switching will work. Accessing the rear panel to do this is getting tedious smile

Ideas anyone ?
_________________________
Double drywalled, "Green Glue" treated Theater
GIK acoustic treatment
Epson 8700UB Projecting on a 135" Seymour XD Audio transparent screen
Outlaw 976 Processor
Outlaw 755 amp for Center and all four surrounds
Adcom GFA 555II for Main L & R channels
Behringer EP4000 for two homemade subs
Outlaw Ultra X13 for REAL Sub Bass !
OPPO BDP103, Marantz CD63SE, Denon DP300F
2 Adcom ACE515s for AC current treatment
Newport Theater Director for AC distribution.
Speakers are all built by myself utilizing Dynaudio Drivers
Second room: Yamaha receiver, Musical fidelity X10D tubes, Carver C9 holographic pro.

Top
#99364 - 11/12/24 04:12 PM Re: Trigger operates sporadically [Re: kiwiaudio]
The Wyrm Offline
Deputy Gunslinger

Registered: 05/04/15
Posts: 3
Loc: Florida
I wish I knew what to tell you. I have a 976 feeding a 7900 but haven't had an issue like this. But at least you know there is someone listening. I haven't been active in a little while and I was shocked to see there was no one here when I found the saloon again last week. Still some good products here, but not like before. I love my Outlaw Audio gear. Good luck to you!
_________________________
Epson 5050UB
Outlaw Audio Model 976
Outlaw Audio Model 7900
SVS Ultra Towers, Center, and Surrounds
Rythmik Audio FV15HP Subwoofer

Top
#99365 - 11/15/24 11:35 AM Re: Trigger operates sporadically [Re: kiwiaudio]
butchgo Online   content
Desperado

Registered: 06/22/07
Posts: 373
Loc: Southern Oregon coast
I had this problem with one of my XPA-1L amps and I finally had to pop the cover off and play with the trigger jack connection.
This fixed the problem.
You might try to see if you can clean the inside of the connection somehow with a little isopropyl alcohol.
_________________________
Epson 3500 3D projector
93" Carl's Place Flexiwhite DIY screen
Outlaw 976 Pre/Pro
Outlaw 7500 for center and surrounds
2- Emotiva XPA-1Ls for LF/RF duty
2- Outlaw LFM-1 EX subs
Oppo BDP-105 Blu-ray/DVD/SACD player
Outlaw LCR (Snell Labs) for center channel duty
Tekton Lore monitors L/R
4- Emotiva ERD-1s surround speakers
Monster HTS3600MKII power center

Top

Who's Online
0 registered (), 287 Guests and 1 Spider online.
Key: Admin, Global Mod, Mod
Newest Members
audio123, Dustin _69c10, Dain, REP, caffeinated
8717 Registered Users
Top Posters (30 Days)
The Wyrm 3
butchgo 2
FAUguy 2
kiwiaudio 1
Forum Stats
8,717 Registered Members
88 Forums
11,331 Topics
98,708 Posts

Most users ever online: 884 @ 11/01/24 01:32 AM