#72361 - 11/03/06 12:29 PM
No Volume control on 1070
|
Deputy Gunslinger
Registered: 08/07/06
Posts: 4
Loc: NY
|
This is very strange, but a 1070 has simply lost volume contol. The remote does not adjust master volume, and turning the 1070 vol control does *nothing*... was working fine, and I'm sure something was changed but I am stumped! I did fully power down, and power up. I can change inputs and run other menu items... just no volume control!
What should I be looking for here?
|
Top
|
|
|
|
|
#72363 - 11/03/06 01:05 PM
Re: No Volume control on 1070
|
Deputy Gunslinger
Registered: 08/07/06
Posts: 4
Loc: NY
|
Thank for your quick reply gonk. This is troubling... I went to the unit to double-check the power-on default volume levels... So once again, I put into standby, Powered off, powered on, pressed standby and guess what? I now have audio, and can control with both the know and the remote. I had just done this two times prior to sending to the forum.
FWIW: One fairly recent change was adding a 2nd set top box. (A DISH sat receiver) Prior to this, I had a Microsoft MCE server and a Cable set-top box (CableVision, which I think is scientific) Even with the DISH it all worked for several days before this issue however.
Below is what I was ABOUT to post to you:
-Turning the front knob has NO effect -No sound at all from 1070 -No headphones plugged in and the level is full off -Power on default volume had not been changed that I recall, but when I went to check and restart .. as I mentioned above it seems to be working again!
|
Top
|
|
|
|
|
#72365 - 11/03/06 07:35 PM
Re: No Volume control on 1070
|
Deputy Gunslinger
Registered: 08/07/06
Posts: 4
Loc: NY
|
It was defintately not -7-dB... I think it was -30dB. At one point (after many remote vol + presses with seconds in between presses) the display did change. I forgot to mention this before, sorry. But it only changed that one time. (I think from -30dB to something like -22dB) After that, no amount of vol + / - on the remote or the front knob had any effect, and there was no audio out, even after two full power resets of all gear. The 3rd time, as I mentioned seemed to work.
I have a support call open on this, and they seem to think it has to do with firmware, but I applied the update to this and another 1070 in a seperate room about two months ago. (the other 1070 btw has the EXACT same equipment connected and has not had this issue)
So for now, it's unsolved but working. I'll post any findings. Thanks for your time on this gonk! Much appreciated. Don
|
Top
|
|
|
|
|
#72366 - 11/04/06 09:24 PM
Re: No Volume control on 1070
|
Gunslinger
Registered: 08/26/06
Posts: 18
Loc: Harleysville, PA
|
I had the exact same problem a while back. I applied the "no audio" firmware upgrade and haven't had that exact problem since.
Now, occassionaly after I power on the receiver, I get the no audio problem. But if I switch the input to another source the audio comes on....
_________________________
Outlaw 1070 Definitive Technology Reference RLS-II, front in-walls Definitive Technology BP/A, rear in-walls Def Tech Mythos Seven, center Polk Audio Atrium 55, outdoor patio SVS PB12-NSD Paradigm CS-50R, in-ceiling kitchen Paradigm CS-50R, in-ceiling dining room Adcom GFA 535 Yamaha M-35 Sony DVP-NS75H DirecTV Plus HDDVR Toshiba 50” Plasma, 50HP66
|
Top
|
|
|
|
|
#72367 - 11/05/06 01:26 PM
Re: No Volume control on 1070
|
Deputy Gunslinger
Registered: 08/07/06
Posts: 4
Loc: NY
|
Interesting. I did in fact try switching inputs back and forth several times between the three sources I have configured, but it did not help. I also had gone through setup to make sure that the config was correct for each source, and it was.
I also did not mention this earlier, but I am using only digital inputs in this setup. (on both 1070s... as I mentioned, I have two purchased at the same time with identical sources configured and both have been flashed) -The MCE server is connected via TOSLINK 1 -The cable set-top box is connected via RCA 2 -The Sat set-top box is connected via TOSLINK 3 The output is a 5.1 config
|
Top
|
|
|
|
|
#72368 - 11/10/06 04:58 AM
Re: No Volume control on 1070
|
Gunslinger
Registered: 07/03/01
Posts: 104
|
I've had an issue like this a couple times before. For me at least, it seems to be connected to the loose optical cable on my PC end. (The output isn't deep enough for it to snap in properly.) If the cable comes out while the source is being used, then i have an issue like this, that is fixed by switching the receiver into standby and then back on. Could this possibly be whats happening with you?
|
Top
|
|
|
|
|
#72369 - 12/03/06 07:25 PM
Re: No Volume control on 1070
|
Gunslinger
Registered: 08/26/06
Posts: 18
Loc: Harleysville, PA
|
Okay.... Now I'm having this problem with a lot more frequency... One thing I noticed is that the volume level readings do change (i.e. -32db to -28db) however, no audio is heard from the speakers. To unfreeze, I select another input (however, the new input must have an active signal) or I power the unit off, then select another input with an active signal to power on...
Also, periodically, I get garbled audio, which I must power the system on & off to clear... Just this weekend, audio went out in the middle of playing... I had been listing to CD's & my iPod (thru the Aux input) for about 2 hours, when the sound stopped. Again I power on & off, the sound returned.
Does anyone know the definitive solution to these audio problems???
The 1070 sounds GREAT, Really it DOES!!! But with all the quirks/bugs... is it all worth it? I was considering getting the Rotel 1057 when I brought this, I'm beginning to think maybe I should have spent the few extra hundred to get the Rotel...
_________________________
Outlaw 1070 Definitive Technology Reference RLS-II, front in-walls Definitive Technology BP/A, rear in-walls Def Tech Mythos Seven, center Polk Audio Atrium 55, outdoor patio SVS PB12-NSD Paradigm CS-50R, in-ceiling kitchen Paradigm CS-50R, in-ceiling dining room Adcom GFA 535 Yamaha M-35 Sony DVP-NS75H DirecTV Plus HDDVR Toshiba 50” Plasma, 50HP66
|
Top
|
|
|
|
|
#72370 - 12/04/06 12:18 AM
Re: No Volume control on 1070
|
Deputy Gunslinger
Registered: 11/16/06
Posts: 11
|
Interesting.... I just received my new B stock 1070 a few days ago, and I'm having very similar problems. Not with the volume control, but the other stuff you mentioned. Plus, the output to my subwoofer goes dead sometimes when I first turn on the receiver, or when I change sources or surround modes.
And just like your unit, I have to fool around changing sources or turn the unit off and back on again to fix these problems.
I've been thinking my problems were probably because this was a B stock unit that had been returned and not thoroughly checked out by Outlaw. But now I'm beginning to wonder......
Like you said, this is one GREAT sounding receiver (I was stunned by the sound quality when I hooked it up), but maybe just not worth the hassle.
|
Top
|
|
|
|
|
|
0 registered (),
92
Guests and
2
Spiders online. |
Key:
Admin,
Global Mod,
Mod
|
|
|
8,714 Registered Members
88 Forums
11,330 Topics
98,700 Posts
Most users ever online: 579 @ 07/06/24 02:31 PM
|
|
|
|