#53084 - 05/11/05 06:49 AM
Different Configurations for Different Rooms???
|
Gunslinger
Registered: 06/14/04
Posts: 99
Loc: New City, New York, USA
|
Is there any way with the 990 to have a different speaker setup configuration for each of two different rooms??
For example, to run the autosetup for one room, save it, and do the same for the second room (say, a home theater room, and an audio only room).
Also, how could one get the rs232 specific codes to control the various parameters of the 990? I figure that the different room configurations could be sent from a computer, if the 990 couldn't save them by itself as separate configurations.
Any thoughts on this???
|
Top
|
|
|
|
|
#53086 - 05/11/05 09:51 AM
Re: Different Configurations for Different Rooms???
|
Desperado
Registered: 04/19/05
Posts: 361
Loc: Plano, TX
|
There are very few pre/pros out there, aside from dedicated multi-room units, that configure channel settings for more than one room, and even fewer that route digital signals to second/third rooms. Even much pricier pre/pros (i.e., the $6K Halo C1) only send out analog signals for their configurable outputs.
There's good reason for this - since the signal has to be in a format that will support both 990 volume control or secondary volume control (wall volume control, 2nd pre/pro or music distribution system), analog is the only way to accomplish this.
To my knowledge, the only one-box unit that configures speakers for two separate rooms is Denon's ridiculously huge AVR-5805 multiroom receiver.
_________________________
--Greg
|
Top
|
|
|
|
|
#53087 - 05/11/05 11:02 AM
Re: Different Configurations for Different Rooms???
|
Gunslinger
Registered: 06/14/04
Posts: 99
Loc: New City, New York, USA
|
Appreciate the responses.
What I would be doing is simply changing the parameters for each room (ie spkr distances, number of speakers, etc, and perhaps even using the autosetup for each room (Gonk...as if each room were the ONLY room).
I have in place NILES switching devices, to make the change to each room, so as far as the 990 is concerned, it only knows about one room.
Thus, I want to change the parameters of the 990 "on the fly" either directly with discrete remote codes or via the 232 interface, using direct commands.
With specific 232 commands (or discrete ir commands), hopefully this would be doable.
|
Top
|
|
|
|
|
#53088 - 05/11/05 11:50 AM
Re: Different Configurations for Different Rooms???
|
Desperado
Registered: 03/21/01
Posts: 14054
Loc: Memphis, TN USA
|
Are you planning on using the 990 to run two multichannel rooms? Or will one room be stereo only?
If it is two separate multichannel rooms, the 990 does not support the ability to have two sets of system settings (speaker distances, crossovers, trim settings, ...) stored at once, making this arrangement very much not optimal. This is true of most any pre/pro, especially at the price of the 990 - it would be more effective to get two pre/pros and assign each to a different multichannel system.
If one space is multichannel and one is stereo, the stereo space doesn't need speaker distance settings or other such adjustments (all of these are things that were added to deal with the challenges of 5+ speakers). Those settings would all be set to serve the multichannel main zone. Think of the second zone as an analog pre-amp with composite and s-video switching that happens to be tucked into the same cabinet as the 990: you can select any stereo analog source and control its volume independently of the main system. The zone 2 remote gives you the ability to directly control turning the zone on/off, changing the zone volume, muting the zone, and selecting the zone input.
|
Top
|
|
|
|
|
#53089 - 05/11/05 12:58 PM
Re: Different Configurations for Different Rooms???
|
Gunslinger
Registered: 06/14/04
Posts: 99
Loc: New City, New York, USA
|
Thanks Gonk for the reply....
Yes indeed, both rooms are multichannel.
Would it not be possible to have either one of the following options:
Use a home automation computer program such as HAI, to automatically send a sequence of rs232 commands to the 990, for each of the rooms. The command sets would contain all of the needed parameters such as distance, etc. Obviously one would need to know the command codes for each parameter...which hopefully are available.
The other option would tbe to do the same, but instead of rs232, using IR if indeed, discrete codes were made available for the individual parameteres.
Wonder if Scott has any info on specific 232 commands for these parameters, and/or IR discrete commands......
|
Top
|
|
|
|
|
#53091 - 05/11/05 01:33 PM
Re: Different Configurations for Different Rooms???
|
Gunslinger
Registered: 06/14/04
Posts: 99
Loc: New City, New York, USA
|
Indeed, the preamp outputs, and the video outputs, are respectively being routed to NILES switching devices. The latter are controlled by voltage triggers, set off by the HAI home automation program. Thus I am able to drive EITHER of two multichannel rooms with no problem.
You are correct in that for each room, I would be going through the menu to change the parameters OR if the 990 allows it, to send out macros either through a string of 232 or IR commands.
|
Top
|
|
|
|
|
#53092 - 05/11/05 01:42 PM
Re: Different Configurations for Different Rooms???
|
Gunslinger
Registered: 06/14/04
Posts: 99
Loc: New City, New York, USA
|
Indeed, the preamp outputs, and the video outputs, are respectively being routed to NILES switching devices. The latter are controlled by voltage triggers, set off by the HAI home automation program. Thus I am able to drive EITHER of two multichannel rooms with no problem.
You are correct in that for each room, I would be going through the menu to change the parameters OR if the 990 allows it, to send out macros either through a string of 232 or IR commands.
|
Top
|
|
|
|
|
#53093 - 05/11/05 02:00 PM
Re: Different Configurations for Different Rooms???
|
Gunslinger
Registered: 04/28/05
Posts: 269
Loc: Canada
|
It also sound like then we should be able to connect the unit to a PC, have an motion detector figure out where we are in the room and dynamically change the surround output as we move through the room in real time... LOL Whats the BAUD rate on the port? ![wink wink](/ubbthreads/images/graemlins/default/wink.gif)
|
Top
|
|
|
|
|
|
0 registered (),
92
Guests and
2
Spiders online. |
Key:
Admin,
Global Mod,
Mod
|
|
|
8,714 Registered Members
88 Forums
11,330 Topics
98,700 Posts
Most users ever online: 579 @ 07/06/24 02:31 PM
|
|
|
|