I will second that it is not unique to the 770. The only reason an amp "pops" is when it is triggered on. If it pops more than that it is defective.

Here's a workaround for your popping problem: Signal the amplifier(s) off of the multi-zone DC trigger output on the 950 instead of the main one.

The proper way to start up or shut down ANY decent audio system is to turn on sources and preamp first and power up the amp(s) last. When you shut a system down the amp(s) should be powered off first, then the preamp, and then any remaining sources. By doing this you are virtually guaranteed to not get pops or other speaker damaging noise. Once you switch the trigger connection all you have to do to control the amp(s) is to turn on or off the multi-zone feature in the 950’s menu. I would also recommend engaging the multi-zone "MUTE" feature so that the amp(s) receives no input in this mode. You can still control the whole system from your recliner but it takes two or three extra keystrokes and those can be programmed into startup/shutdown macros if you like. I’m using three Aragon 8008ST amps with Klipsch Cornwall mains/surrounds and they will pop fairly loud unless sequential switching is utilized. By moving the trigger cable and programming the extra keystrokes into a macro on the remote you get the same ease of use without spending money. Obviously this won’t work for those who use the multi-zone feature for its intended purpose but I would be willing to guess that most people won’t use the second zone anyway. OR, you can buy a sequenced surge protector (Niles, Monster, etc.) that will do this automatically but prepare to give up $200.00 and up (mostly up) to get sequential switching.

As to whether a pop is "normal" or not, "normal" doesn't mean it won't eventually kill your speaker's drivers. Take the grilles off your speakers and watch the woofer cones when any "pop" occurs. If the cone is barely moving it probably won't damage your speakers but if the cones move very far (more than about 1/32") you're taking chances on your driver's longevity.

Hello All,
I'm currently using a Monster HTS5000MKII for my main rack and one of the smaller units for my subwoofer (on a different outlet). This has eliminated all hiss and ground-loop problems. The sequential switching has eliminated any 'popping' problems. The benefits of a high quality power conditioner are audible also. I wouldn't have believed it, but my bass frequencies are more well-defined since my installation of the Monster.
As far as leaving your gear powered-up all of the time, one theory is that if you leave your equipment on all of the time the temperature and humidity inside the equipment will remain more constant. This will lessen any condensation and/or power-up surge wear-and-tear. In multiple professional venue installations, I've seen amplifiers left powered-up for over five years at a time. From installation to replacement. This enabled the amp racks to remain locked and untouched by unauthorized hands. Personally, I turn my stuff on and off per usage. If I were in an area of higher humidity, then I would leave it on.
Once again, I'd like to say thanks to the Outlaws for providing a refreshingly unbiased forum for good audio/HT discussion.
(Where's my 950!)
On an off-topic, I'm enjoying the 1050 and find it to be a high-quality, well-built piece of gear.
'Till next time,
Mix

My 755 pops, too. It has nothing to do with sequence; if I turn the system on, then turn off just the amp, and then turn it back on again, there is a pop. It sounds like it comes both from the amp itself, and from the speakers, with the pop noise from the amp being the louder pop. When I turn on the whole system at once, with the trigger, the pop comes a short while after the 950 comes on, owing to the 755's built-in delay. I don't think triggering the 755 off the 950's multi-zone trigger will change anything. I also don't think the speaker pop is loud enough to damage anything. The speaker pop seems to be pretty much independent of the 950's volume control; I don't think the 950 is in any way causing the pops.

------------------
Matthew J. Hill
matt@idsi.net

The pop is not coming from the 950. It happens whether or not I trigger the 770 or just power it on. Yes, all of the other components were already on first. I solved my problem, but not really to my satisfaction. I am just leaving the amp on all the time now.

I don't think the pop sound is hurting the speakers. I watched the drivers and although I think they moved very slightly, most of the actual sound appears to come from the amp itself. I am going to ask Outlaw about this directly...I will let you all know if I hear anything else.

Thanks!