The Amplifier Section, Class AB and AClass AB and A amplifiers are similar, so we'll discuss both here. Class AB amplifiers have transistors that pull up to the positive rail and transistors that pull down to the negative rail. This corresponds to the action of pushing the speaker cone out and in.
Class AB means that the output transistors do not always have current on them. For example, when the upper transistors are pulling up towards the positive rail (pushing the speaker out), there is no current in the lower transistors. When the output signal swings through zero, towards the negative rail, the output transistor must go through a transition from zero current to a non-zero current. The best analogy that I can think of is driving an old car with too much slop in the steering. As you go from one side of the road's crown to the other, the steering crosses a "dead" zone, and you tend to over-steer. Special temperature compensated bias circuitry reduces this dead zone, known as notch distortion. The figure below shows the output of a class AB amplifier with too little bias and the resulting distortion. Notch distortion increases at higher frequencies and low volume levels. Some modern designs have reduced this type of distortion to very low levels.
Class A means that every transistor is always conducting current. They are very similar to class AB amplifiers, but the bias circuitry is set so that there are very high currents in the output transistors. Because these amplifiers do not have this "dead zone', less feedback is required to achieve low distortion.
A 100 watt amplifier may dissipate nearly 100 watts internally even when there is no audio output. This type of design is impractical in the harsh auto environment. Many class A amplifiers pedaled for the automotive market are not really class A. They are huge power wasters in the home as well.
Input and Driver Stages
The amplifier works this way: A small audio signal is presented to the amplifier's input. Transistors are not linear, which means that the input signal will distort somewhat as it passes through the various amplifier stages. To correct this distortion, a portion of the output is compared with the input. The difference creates a correction signal reducing this distortion. The input stage is a special type, called "differential". It has a + and a - input because it must accept both the audio input and the input from the feedback circuitry. Excess feedback can lower distortion dramatically, but cause instability. Careful design rules must be followed to avoid this instability.
The output of the input stage feeds into the driver stage. The driver stage may use one, two, or three devices. Often this circuitry is referred to "Darlington", or "Triple Darlington". The driver circuit feeds the output stage, which may have two, four, six, or more transistors. The more output transistors, the better. Multiple output devices reduce distortion (requiring less negative feedback) and improve reliability.
Bipolar or MOSFET?
We have seen both MOSFET (Metal Oxide Silicon Field Effect Transistor) and Bipolar transistors used in audio amplifiers. Claims have been made that each is superior. I have seen claims that MOSFETs have a tube ("Valve" for the Brits) sound. This is more folklore. The musicians and their instruments are supposed to have "the sound", not audio equipment! MOSFETs are tougher than Bipolars, and can pull closer to the supply rail. It takes more Bipolar transistors to achieve the same power as a MOSFET, therefore Bipolar amps tend to be more expensive. But, MOSFETs are very non-linear, compared to Bipolars and require much more feedback to achieve reasonable distortion numbers. They are a great choice for bass amps, as low frequency audio is not difficult for a MOSFET. The most expensive car and home amplifiers almost always use Bipolar transistors.
Efficiency
What makes an amplifier get hot? Both the power supply and the power amplifier generate heat. The maximum efficiency of the power supply is nearly 100%. Good power supply designs, with the highest quality components approach 85%. The class AB amplifier efficiency at full power can approach 75%. The total efficiency, including the power supply, can be about 65%. But, efficiency drops at lower power and can typically be under 20%. A class AB amplifier actually runs cooler at full power than it does at half power. Run this amplifier into clipping and it might run even cooler! Where is all this power going? The output transistor is basically a large variable resistor. If the instantaneous output voltage should be 40 volts and the power supply is 100 volts, then 60 volts must be "wasted" in the output transistors. Driving a reactive load (like a speaker) causes the efficiency to drop ever further. This brings us to the other audio classes designed to improve efficiency.
Class D
First, let's dispel another myth: Class D does not stand for digital. The input is converted to a two-state (binary) representation of the audio waveform. That's where the similarity ends. This distinction is important because class D doesn't provide the benefits normally associated with digital components.
That being said, class D designs dramatically improve efficiency. Instead of wasting power in the output transistor, the output is switched at a very high frequency between the positive and negative supply rails. If the output is to be zero, then the waveform is at a 50% duty cycle. If the output is to be a positive voltage, then the duty cycle would be greater than 50%. Because the output devices are either completely turned on (no wasted voltage) or completely turned off, theoretically efficiency is 100%. So the audio input must be converted to a pulse width modulated waveform (PWM). The yellow trace below is the output of the amplifier; the blue trace is the PWM waveform. The blue waveform is fed to an output filter, which results in the yellow output waveform. Notice that the output looks somewhat distorted. All of the switching noise and distortion cannot be removed and the result can be seen here. Because of this process of converting the input signal to PWM and converting back to analog, a good deal of distortion is introduced. Conventional feedback like that used in class AB designs is used in these amplifiers to reduce distortion.
MOSFETs are the only choice for class D designs. Most class D designs are useful only for bass amps as they can not switch fast enough to reproduce high frequencies. Some high quality, full range class D designs exist for pro audio, but they are complex with multi-phased outputs.
Class T
Class T (Tripath) is similar to class D with these exceptions: This class does not use analog feed back like its class D cousin. The feedback is digital and is taken ahead of the output filter, avoiding the phase shift of this filter. Because class D or T amplifier distortion arises from timing errors, the class T amplifier feeds back timing information. The other distinction is that this amplifier uses a digital signal processor to convert the analog input to a PWM signal and process the feedback information. The processor looks at the feedback information and makes timing adjustments. Because the feedback loop does not include the output filter, the class T amplifier is inherently more stable and can operate over the full audio band. Most listeners can not hear the difference between class T and good class AB designs. Both class D and T designs share one problem: they consume extra power at idle. Because the high frequency waveform is present at all times, even when there is no audio present, the amplifiers generate some residual heat. Some of these amplifiers actually turn off in the absence of music, and can be annoying if there is too much delay turning back on.
Class G
Class G improves efficiency in another way: an ordinary class AB amplifier is driven by a multi-rail power supply. A 500 watt amplifier might have three positive rails and three negative rails. The rail voltages might be 70 volts, 50 volts, and 25 volts. As the output of the amplifier moves close to 25 volts, the supply is switched the 50 volt rail. As the output moves close to the 50 volt rail, the supply is switched to the 70 volt rail. These designs are sometimes called "Rail Switchers". This design improves efficiency by reducing the "wasted" voltage on the output transistors. This voltage is the difference between the positive (red) supply and the audio output (blue). Class G can be as efficient as class D or T. While a class G design is more complex, it is based on a class AB amplifier and can have the same clean characteristics as well.
Class H
Class H is similar to class G, except the rail voltage is modulated by the input signal. The power supply rail is always just a bit higher than the output signal, keeping the voltage across the transistors small and the output transistors cool. The modulating power supply rail voltage is created by similar circuitry that you would find in a class D amplifier. In terms of complexity, this type of amplifier could be thought of as a class D amplifier driving a class AB amplifier and is therefore fairly complex.
How to Choose?
Regulated or unregulated? Class AB, D, or T?If you're really into a lot of bass, the class D or T may be for you as these amplifiers will produce the highest SPL with the smallest size. If you just want to wake the neighbors, blur your vision, or make a big splash in SPL contests, maybe you just need one of the inexpensive, powerful, & dirty class D designs. Want the cleanest high frequencies? Maybe a good class AB amp would be your selection. Whatever you choose, I hope this information helps you achieve the sound you're looking for!
Amplifier section.
Regulated power supply.
Output and power supply rails.
12 Volts, switched at 100 kHz.
Input comparator and driver stage.
Underbiased AB stage distortion.
The amplifier output stage.
Class D and Class T waveforms before and after the output filter
Class D/T amplifier.
Class G "Rail-Switcher"
Class H modulated supply.
Previous Topic
Index